DIY Poker Table Part Deux

Ok... So now I'm ready to finish this thing....

Time to finish cutting the rail!

Batterys are charged and everything's a go!

The rail was pretty slender, and I was having a hard time keeping it up while I cut, so I used the corner pieces I cut off yesterday to prop them up around the table while I cut!


Ok! So the rail is cut!


But I've been thinking all day about how the sides of the table are going to show and be bare.... so I do some more online reading.....

Apparently, I should have trimmed 1.5 inches off the sandboard to use as a base for the rail, and then trimmed the base as well.

Well, I didnt do this, so I'm thinking 'I'll just wrap the whole fucking edge of the table in vinyl, and be done with it....'

Then when I get home, I'm like 'nah! I got to do this shit right!!'

So, how do you take an oval, and measure 1.5 inches all the way around it?

I know your answer Lee and Jay: A Router!

Well I don't have one..... so it's ghetto time!

What does a broke mofoco do when he needs to measure 1.5 inches around an oval?

First he gets himself a 1.25 inch piece of 1 x 1


Then, he finds a nice small piece of plywood, and uses his nail gun to attach the two....


Then he grabs the one tool no man should be without.....

DUCT TAPE!!

And tapes a pencil to the end. Then butts the plywood up against the racetrack, and runs it around the edge.....


Ahhhh yeah......

Worked like a goddamn champ!

Now to cut it off. Again, the racetrack will be visable, so I drilled a hole on the the side I was cutting off, to fit my jigsaw in.... This will be covered with vinyl so hopefully it won't be noticable. (I'll let you know when I'm done!)


So I cut out the 1.5 inches!!

I also find that this is sagging bad, and no matter how i place the sawhorses, i'm scared it's gonna break....

Metal ruler and square to the rescue!!


Be sure to mark the ends again! I soon figure out why this is important! :)


Ok! After you trim the 1.5 inches off the racetrack, guess what!!??!!

You also have to trim it off the base! Easiest thing, lay the new sized racetrack on the base and trace! DO EET!


Ok, being that this is the base, I didn't really worry about nice cuts, and jammed the jigsaw through the cuts. A bad cut on this board can't be detrimental i'm thinking.... So rather than waste my time trying to hold up the 1.5 inches, I cut it off when possible....

I just ran to the edge when thigs got hairy, and said fuck it... it's all garbage anyway....

Heres the board after it's been cut...


Ok, now that i have the 1.5 inch cut from the racetrack, I think I'm good to go! Take some wood glue and glue that shit together!

SSSSSCCCCRRRREEEECCCCHHHH!!!!!!

I glued the wrong goddamn sides together! I EVEN MARKED THE FUCKING THINGS!!!!

Oh well, rip em apart and take a rag and wipe off the glue!!

Then, glue them right:


I put paint cans and shit on them, cause I aint got no clamps... Actually I got two.... WOW!

Here is what the rail should look like, with the 1.5 inch piece glued to it:


Thats upside down. It should fit snug around the racetrack now... and the base, which should be the same size as the racetrack....

GODDAMN! I should read more before jumping headfirst into shit! Oh well... It all worked out!

So now, lets put the base down.... put the racetrack on top, put the playing field in place, and put on the rail..... lets see how it all goes together....


Snug as a motherfucking bug in a motherfucking rug!!

Damn, I can just see it now! SWEET!

Ok, back on track... next step...

We need to take Tee Bolts and mount them in the playing field, so we can mount IT to the base!!!

I get 5/16 x 3/8 tee bolts... no sweat....

First thing is to start a 7/8 hole with a paddle bit, and then finish it up with a 3/8 bit all the way through the playing field, and the base.....


I did 8 around the field... 1 on each end, and 3 down each side!


After the holes are drilled, take the Tee bolt, and put it in.

Doesn't fit? Imagine that!

This is my favorite part......

If it doesn't fit, FORCE IT!

Bang it in with a hammer!!!!


Nice fit!

OK, do that all the way around the playing field....


Now we get to start putting on material!!!

I used headliner foam for the playing field... I got it at JoAnn Fabrics...

Take it, and spread it out....


Then take some spray adhesive, and spray it all over the top of the playing field piece of wood (which in my case is the center of the sandboard)


I sprayed this shit on liberally.... I did like 2 coats... I didnt know how strong it was, so I figured I'd go balls to the wall.....

Spray it on, then flip the board over onto the foam!

After you flip the board, either clamp it, or load it with some weight....


While you're waiting for the glue to dry, read the instructions....

There is no better time to read the instructions for something until AFTER you've used it!!

"Note:Not recommended for bondng automotive headliners or expanded polystyrene foam."

Holy shit! What the fuck!

Oh well, too late now.....

Trim the excess off while it dries...


Well, after about 45 miuntes, it seems to be dry, so I check it out...

Seems good.... even though it IS automotive headliner....

Let's check out the playing field with the racetrack on....


OMG! I think I just creamed myself! That looks so SWEET! Im seriously thinking about just leaving it "AS IS" because cards slide superfast across the headliner foam...

But then I gain sense, and realize.... It needs to be covered!

I enlist the help of my son, and we get'er'done!

First, lay out the material, then lay the wood on top, foam side down!


Then grab your stapler.....

Have one person pull the fabric VERY TIGHT, while you staple.....


Joey did the pulling.... I did the stapling!!

After you staple all the way around the playing field, you need to trim the exscess... I trimmed down to about an inch within the staples....


Once, it's trimmed.... there should only be a little bit of material beyond the staples. We dont want to have the table not fit becuase of outside influences!!!

Ater Joey and I put the fabric on the playing field, I couldnt wait to see the rest of the world.....

TIME TO POLY THE RACETRACK!!


I was debating what to do with the racetrack...

My buddy Lee suggested Poly..... He ws right... it looks sweet!!! I do need some glossy ass lacquer or somthing, but it looks sweet!

You know we cant go without checking all the pieces out:


Joey's ready to play...

this table is gonna be SWEEET!!!!!!

Labels: ,